Home > Error Code > Cal Spa Error Codes

Cal Spa Error Codes

Contents

Check to ensure no shutoff valves (if equipped) are closed and that all jets are open. Add Sanitizer according to Manufacturers Instructions.Note: If you do Not have an ORP Sensor installed in the Spa System, you should Never get this Message. Rotomolded Spas Spa Preppers - Hurricane Spa Protection Hot Tub Circulation Pump Troubleshooting How to Measure for a Hot Tub Cover Hot Tub Electrical Safety Spa & Hot Tub Plumbing Fittings Doing so may cause damage to the pump and cause the system to go into an overheat condition.If after repeated attempts (hours apart) you still cannot get all pumps to prime, http://wipidigital.com/error-code/sma-error-codes.html

Press any Button except "Jets 1" to Exit and Return to Normal Operation. If the problem persists, call customer service. (May appear temporarily in an overheat situation and disappear when the heater cools.) 5A, 5b, 5nA, 5nb Sensors are out of balance. After the water cools, a high limit switch may be need to be reset on some spa packs; look for a red reset button. Water temperature is unknown. 2. http://www.hottubworks.com/blog/spa-hot-tub-error-codes-oh-ohh-omg/

Cal Spa Error Codes

So before pressing any buttons, verify that water is flowing from the circ pump outlet. Sign In All Activity Home Theme Default (Default) Copy of Default Contact Us PoolSpaForum.com Community Software by Invision Power Services, Inc. × Existing user? If your water flow is perfectly fine, then you could have a problem with the thermostat or high limit switches used on older spa packs, which could fall out of calibration,

  • Turn OFF the Power to the System and Turn it back ON again to put System into Priming Mode.2.
  • If spa will not reset after spa has cooled, turn off power for approximately 30 seconds and then turn power back on.
  • Not even the light will turn on.
  • Jax K · 8 years ago 0 Thumbs up 0 Thumbs down Comment Add a comment Submit · just now Report Abuse You are both young, and so experimentation is completely
  • Clean and Condition Spa Cover per Manufacturers Instructions.
  • Blocked Suction Fitting.3.

You should be able to set the filtration cycle to FC to accomplish this. Too Many Closed Jets.6. It will run on high and was able to raise the temp a few degrees. Balboa Hot Tub Error Codes Guys like to see what other guys look like, especially when younger, simply out of curiosity and for comparison.

Back to Top Snb, Sb, or SENSOR B SERVICE REQD Message "Sensor B" (Snb or Sb) is Not Operating Correctly.The Sensor Connected to the "Sens.B" Connector on the System Board may Hot Tub Error Code Oh The Water Temperature will probably drop Below Set Temperature between Filter Cycles. Contact your Dealer or Service Organization.A Sensor Failure Message may indicate Excessively High Heater Temperatures which can Scald or Burn!If the Heater is Not Cool Enough to Safely Service, allow the http://www.calspas.com/message-troubleshooting.php BUT, you helped me figure out what part I needed for my hot tub and I really appreciated that:) I will highly recommend your website to anyone needing parts/and or service!!"

Remove, Clean, and Reinstall Spa Filter Cartridge per Manufacturers Instructions. Cal Spa Oh Code If there is Now a "PSt" or "PERSIST FAIL" Persistent Memory Error Message, contact your Dealer or Service Organization. Trending Now Matt Holliday Luke Bryan Patti Smith James Taylor Plaque Psoriasis Treatment Oil Change Coupon Chicago Bears Cheapest Disney Tickets Naomi Judd Santa Tracker Answers Best Answer: HH code on Quick View Jump to content Existing user?

Hot Tub Error Code Oh

The spa topside panel messages include common diagnostic messages, operational messages, and various other messages such as reminders. Get More Information Do not do this more than 5 times. Cal Spa Error Codes Press Any Button to Reset and Clear the Error Message.3. Cal Spa Error Code Ec You can troubleshoot both problems by setting the tub to run continuous filtration cycles for several days.

Press any "Cool", "Warm", or "Temp" Button to Exit Priming Mode.3. this content If a continuously running low-speed-only pump is only used for filtering (not for heating), that is not called a circ pump, but instead may be referred to as a "continuous filtration Failure to properly service or install spa related components can result in serious injury or death. The most common valve; the tee handle valve, will show that the handle is up, but in many cases the gate is still half closed, make sure that it is open Hot Tub Overheating Troubleshooting

Press Any Button to Reset and Clear the Error Message.3. Send Share This Copyright © 2016. drY, dY Insufficient water detected in heater. http://wipidigital.com/error-code/hot-tub-error-codes.html Contact your Dealer or Service Organization to check the Switch Numbers or Setting Values Displayed, and Correct as Necessary to Match the Equipment in the Spa System, or Continue for a

Safety should ALWAYS be your first consideration! Marquis Spa Error Codes Press any button to reset or wait 15 minutes and spa will automatically reset. Back to Top - - F, - - C, or - - Message The Actual Water Temperature is "Unknown" (- -).Priming Mode has been Exited and the Pump has Not yet

The heat relay is sticking and allowing the heater to continue operating after the pump stops.

Back to Top OHS, OH, or SPA TEMP LMT Message There is an "Over Heated Spa" (OHS or OH) Water Condition.One of the Water Temp Sensors has detected 110°F (43.3°C) Incoming One sensor has detected 118F (48C) at the heater. Do not let the pumps run for a total of more than 2 minutes if they haven't primed by then. Vita Spa Error Codes It was advertised 11/21/2016 11/21/2016 Poolservice123 Was given a Climate Keeper electric oil heater...the top 11/19/2016 11/19/2016 Rico_Soma, eddie22Island I have a Cal-Spas hot tub and I am getting a strange

You Must Press Any Button to Reset when Water is below 108°F (42.2°C). What is the "something" he did? After I refilled it none of the buttons work. check over here I even had the light working which did not work before.

If the Error Message has Not Cleared, the Spa Water is still too Hot to Continue Testing.• Either Wait for the Spa Water to Cool Below 108°F (42.2°C), or Exit Now Thanks for your help. Contact your Dealer or Service Organization.A Sensor Failure Message may indicate Excessively High Heater Temperatures which can Scald or Burn!If the Heater is Not Cool Enough to Safely Service, allow the The jets are not running on low.

Sign In Sign Up Browse Back Browse Forums Blogs Calendar Staff Online Users Activity Back Activity All Activity Search Aquarium PartsBath PartsPool PartsSpa PartsWhite GoodsClearance Items (Bath/Spa) Dealer/Tech ApplicationWarranty InformationProduct Please try again. Thanks again. Share this conversation Related Pool and Spa Questions Question Date Submitted I have an older model Saratoga spa SAR200 that came with our 12/1/2016 12/1/2016 Poolservice123 We have Tub does not seem to be heating.

The Heater will Only operate and Heat up to Set Temperature during the Filter Cycles. Back to Top LF or LOW FLOW Message There is a Verified "Low Flow" (LF) Condition in the Heater.The "HFL", "HL", or "HTR FLOW LOW" Fault has occurred 5 times in