Home > Error Code > Gecko Spa Pack Troubleshooting

Gecko Spa Pack Troubleshooting

Contents

Check the "hi-limit" probe installed on the heater barrel. If that doesn't work then turn it back to its original position, so counter-clockwise, back to its original position and then keep on turning it counter-clockwise up to one turn to Heater is deactivated. Reset fuse 1 or fuse 2 on the circuit breaker when SP-F1, F1 or F3 appear on the display.

Switch closed while pump is deactivated. Spa has shut down. leafgroup.com © 1999-2016 Leaf Group Ltd. Please note that the Balboa Error Codes cover all circuit board manufactured by Balboa including Cal Spa, Marquis Spa, Master Spa and many others. read this post here

Gecko Spa Pack Troubleshooting

I wanted to thank you for your time explaining what I needed, as I wasn't 100% sure if what I was ordering was correct. Tips & Warnings The spa skirt is the space that contains insulation between the outer frame of the spa and the spa itself. Your cache administrator is webmaster.

  1. HFL Substantial difference between temperature sensors detected.
  2. BUT, you helped me figure out what part I needed for my hot tub and I really appreciated that:) I will highly recommend your website to anyone needing parts/and or service!!"
  3. Snb Sensor plugged into jack B is not working.

Spa Builders Spa Side Error Codes For more information regarding Spa Builders tech supportclick here Sn1 Nonfunctional high temperature sensor. References Spa Parts Supply: Troubleshooting Made Easy! Rare system error. Vita Spa Error Codes SEoP Sensor open or disconnected.

Lift the cover off to reveal the LED board. Balboa Error Codes Remove the probe from the heater and then put it back in its original position. FLO Flow Switch (heater is deactivated. http://www.ehow.com/how_7600402_troubleshoot-gecko-spa-pack-control.html Each one uses it's own conventions for naming the various system faults.

Heater disabled but spa operational SH Short circuit on temperature sensor Sn1 Hi-Limit fault, water may be dangerously hot Sn2 Temperature sensor fault, Heater deactivated Sn3 Temperature sensor fault, Heater deactivated Gecko Hot Tub Troubleshooting th3/39 On startup indicates water temperature less than 39° F. Locate a Dealer Get Pricing Name First Last Email* Zip / Postal Code*PhoneQuestionPlease fill in the specifics of your Price Quote Request. I have you guys bookmarked now for all my hot tub needs and will be referring others to ur site because of ur prompt service and very reasonable prices." - Sarah

Balboa Error Codes

FL1 Water flow problem, inhibited or pressure switch malfunction. http://www.spadepot.com/spa-error-codes.htm Contact qualified service technician. Gecko Spa Pack Troubleshooting Pump may also be deactivated). Gecko Spa Control Error Codes Try our site search! *** Search for: *** Close Locate a Dealer Special Offer Download Brochure Get Pricing!

Your local dealer can help you get the best hot tub prices and options in your area. When you look at the spa, you want to make sure that water is flowing in through the skimmer and that there's no obstructions there. Is it an Error Code, or a System Status Code? drops. Hot Tub Error Codes

Spa has shut down OHS Overheat. Not all spa codes are errors, to inform you of trouble, but many codes are used to provide information about system mode, status or equipment operation. The temperature inside the spa skirt is high when the display reads SP-OT. Check the circuit breaker and wiring to see if any fuses have blown.

Categories Consumer Research for Best Hot Tub (100) hottubworks.com (128) life (131) spa chemicals (67) spa covers (161) Spa Crystals (11) spa filter (31) spa heater (26) Spa Ozone (17) Spa Dr Code On Hot Tub COL Cool condition. ICE Freeze protection.

Clean the orange connector's pins with rubbing alcohol and a cotton swab.

Check the LED board to see if there are three flashing dots on it. If water temperature drops 20ºF below set temperature, low speed pump and heater activates to bring temperature within 15º of set temperature. F6 Freeze protection. Marquis Spa Error Codes No action is necessary.

If you did have a filter in, for example, and you got something caught in the system, that can cause a FLO error. Pump may also be deactivated). RH Tubs: Spa Side Control Panel Error Codes Spa Parts Supply: MSPA-MP-CE METAPACK MSPA-MP-SR4-CE VERSION SERVICE MANUAL Photo Credit Jupiterimages/Comstock/Getty Images Promoted By Zergnet Comments Please enable JavaScript to view the Heater disabled but the spa is operational.

This will reset the system. Remove the transformer, which is a small silver rectangle with blue, yellow, white, black and red wires coming out that leads to a plastic orange connector. You may need to replace the pack if the display continues to show the wrong water temperature. drops.

You must be logged in to post a comment. Water temperature has reached 118ºF. Hi limit sensor is disconnected or shorted or the spa temperature is above 112° F. If alternating with temp, may be temporary condition.

ICE2 Freeze protection. The keypads of the Gecko Spa Pack are simple interfaces used to control the day-to-day operations of a spa. Sometimes the spa pack controls will display error codes or flashing lights. In some instances it may be more prudent to contact a local repairman or send Spa Care Center your control box for evaluation/repair.

SP-IN means that the input voltage is low. Spa has shut down. Your cache administrator is webmaster. Sensor plugged into jack A is not working.

I WAS SO IMPRESSED WITH HOW QUICK YOU ANSWERED MY QUESTIONS (ON A WEEKEND ESPECIALLY, WOW!!)" - Cheryl, Lake Stevens, WA "I don't know if u guys monitor this email address Could indicate a flow problem. Your cache administrator is webmaster. About eHow Advertise Write For eHow Contact Us Connect with us Terms of Use Report Copyright Ad Choices en-US Privacy Policy Mobile Privacy leafgroup.com © 1999-2016 Leaf Group Ltd.

System will restart when temp.