Home > Error Code > How To Get Balboa Hot Tub Out Of Sleep Mode

How To Get Balboa Hot Tub Out Of Sleep Mode

Contents

OHS “Overheat”-The spa has shut down. Check for Water Level, Flow Restrictions, Closed Valves, Air Bubbles, and Pump Prime, or Continue for a Detailed Test Procedure.WARNING:A Heater Overheat Error Message may indicate Excessively High Heater Temperatures which If water temperature drops 20°F below set temperature, low speed pump and heater activates to bring temperature within 15° of set temperature. The Water Temperature will probably drop Below Set Temperature between Filter Cycles.Other Heating Modes are Standard, Standard in Economy, and Sleep Modes.Ecn or Ec is ON Solid (Not Flashing):The Current Water

To disconnect you will need open end box wrenches, 1/4 and 3/8. There are two nuts above and below the straps. Too Many Closed Jets.6. On EL and GL Systems Only, equipped with a "Mode" Button, the Ozone Generator can be Turned ON for15 Seconds and OFF by using the "Mode" Button.

How To Get Balboa Hot Tub Out Of Sleep Mode

Sby The hot tub is in Standby mode. Back to Top rtC or RTC FAILURE Message The "Real Time Clock" (rtC) Cannot be Read.At Power-Up, the System Board Real Time Clock could Not be Read. All Reminder Messages can be Disabled through the Topside Panel Users Menu.* Note: The Balboa Default Interval is 180 Days, but some Spa Brands or Models may be Different. Clean and Condition Spa Cover per Manufacturers Instructions.

Contact your Dealer or Service Organization.A Sensor Failure Message may indicate Excessively High Heater Temperatures which can Scald or Burn!If the Heater is Not Cool Enough to Safely Service, allow the Another thing to check is the GFCI cord (if installed) or breaker, to test remove the .3amp fuse marked F4 on the diagram inside the cover of the control system or All Reminder Messages can be Disabled through the Topside Panel Users Menu.* Note: The Balboa Default Interval is 30 Days, but some Spa Brands or Models may be Different. Spa Error Codes LF = Persistent low flow problems. (Displays on the 5th occurrence of "HFL" message with 24 hours).

Contact your Dealer or Service Organization. Std Mode On Hot Tub Check for Water Level, Flow Restrictions, Closed Valves, Air Bubbles, and Pump Prime, or contact us on 023 9232 1719Check for all of the following Conditions:1. MessageMeaningAction Required No message on display. If Not, Continue to Next Step.Spas with Pump Suction Blockage Switch:1.

SE = Spa operating in Standard-in-Economy Mode. Hot Tub Sleep Mode This means that there is a flow issue through your heater. Sign In All Activity Home Theme Default (Default) Copy of Default Contact Us PoolSpaForum.com Community Software by Invision Power Services, Inc. × Existing user? On some systems, an alarm will sound.

  1. This is Not an Error Message.
  2. HFL = Substantial difference between temperature sensors detected.
  3. th2/current temperature = On startup indicates temperature probe problem.
  4. You can skip Priming Mode if you're restarting the spa for some other reason (without the water having been drained since the last time the spa functioned properly).
  5. Pumps and Blower can be turned ON and OFF to remove any Air from the Heater.
  6. All Pumps and Blower are ON for at least 4 Minutes After Temp is 45°F (7.2°C) or Above at the Sensors, or when the Aux Freeze Switch Opens.
  7. Heat Related Pump Not Running.8.

Std Mode On Hot Tub

Heat Related Pump Not Primed. http://www.strongspas.com/common-technical-questionsanswers Rare system error. How To Get Balboa Hot Tub Out Of Sleep Mode Press "Mode" Button to Clear Message. Balboa Error Codes SbY or STANDBY MODE Message The Spa is Operating in the "Standby" (SbY) Mode.All Automatic Spa System Functions are disabled so that Pumps and Blower will not turn ON Automatically.

PSoL = Pressure switch open with low pump. The idea is that, if anything in the file changes, the checksum will change and Result in a CrC Error.At Power-Up, the System has Failed the Program Checksum Test. If the GFCI does not trip for some reason, the gFI fault will appear and the HOt flag will be set.If the spa is subsequently powered down and then powered up All Reminder Messages can be Disabled through the Topside Panel Users Menu.* Note: The Balboa Default Interval is 7 Days, but some Spa Brands or Models may be Different. Balboa Spa Control Manual

If you still have a problemyou either have bad sensor or PC board. It may be possible for a stuck relay to free itself after the power cycle, but the spa cannot clear the the HOt message without starting up in Test Mode first. Back to Top Std, St, or STANDARD Message The Spa is Operating in the "Standard" (Std or St) Heating Mode.Between Filter Cycles, the Water Temperature is Sampled every 30 Minutes. dry = Inadequate water detected in heater. (Displays on third occurrence of "dr" message).

Either wait for the Potential Freeze Condition to End, or contact your Dealer or Service Organization. Balboa Hot Tub Troubleshooting One of the sensors detected 118°F at the heater. Email Address: Password: You will be prompted to enter your password on the next page Create an account Forgot Password?

Temperature will remain close to desired, but it will drop between filter periods 3.

Check for Water Level, Flow Restrictions, Closed Valves, Air Bubbles, and Pump Prime, or contact your Dealer or Service Organization.Check for All of the following Conditions:1. If your display has a mode button Press “Mode” to enter mode programming, press “Cool” to cycle through to desired mode (LCD flashes until confirmed), then press “Mode” to confirm selection. While cleaning your filter make sure there is no debris in your hot tub that will get sucked down into your pump. Master Spa Error Codes Switch closed while pump is deactivated.

Press "Mode" Button to Clear Message. Std, St, or STANDARD Message The Spa is Operating in the "Standard" (Std or St) Heating Mode.Between filter cycles, the water temperature is sampled every 30 minutes. Shut the spa off for 20 min to reset the power. No action is necessary.