Home > Error Code > Jacuzzi Fl1 Error Message

Jacuzzi Fl1 Error Message

Contents

Sn2 Nonfunctional temperature sensor. Refer to your owner's manual. characters left:

Contact Us|Terms of Service|Privacy & Security|About Us|Our Network|Sitemap © 2003-2016 JustAnswer LLC JustAnswer UKJustAnswer GermanyJustAnswer SpanishJustAnswer Japan 426 9456868 Fill out my Wufoo form! Do not enter the spa. Source

Inspect these first:• Check slice or ball valves. OHS = Overheat. If you confirm all those things, and it still throws an Sn error at you, test the sensor as described above; it may be faulty. Water temperature has reached 118ºF. https://www.thecoverguy.com/backyard-blast/jacuzzi-hot-tubs-error-codes-information/

Jacuzzi Fl1 Error Message

drops. Entire system is disabled. Ask for Mrs.

Power failure. Pump may also be deactivated). System will restart when temp. Jacuzzi J 345 Fl1 Error See "Water is too hot" (page 77).

One sensor has detected 118° F at heater. Jacuzzi Hot Tub Error Codes Sensor plugged into jack A is not working. There also could be a voltage problem, excessive voltage creates heat. http://www.spadepot.com/spa-error-codes.htm Hi limit sensor is disconnected or shorted or the spa temperature is above 112° F.SEoP = Sensor open or disconnected.

Power fluctuation in the secondary power line is causing the DC voltage to be low. Jacuzzi Error Code Fl2 If the FL1 goes away and the heat light doesn't come on it might be a bad heater. If display shows only this message (blinking) spa is shut down.HFL = Substantial difference between temperature sensors detected. I have checked all the things the manual suggests (clean filters, water level, hose to filter connections) and a few other things such as starting without filters in place.After searching (this

  • FL Spa water is more than 20° F cooler than the temperature set point.
  • Gecko Error Codes also cover any control box manufactured by Gecko.For information regarding repairs click here If you need further help with troubleshooting click here Balboa | Gecko | Hurricane |
  • Our tub, a Jacuzzi (06) J345 has the dreaded FL1 error code flashing on the display.
  • Spa unusable.
  • If not, cut the power again and remove the filters.
  • The spa deactivates in this situation.DO NOT GET INTO THE WATER.
  • CLOSED or SHORTED FLOW SWITCH ON SYSTEM STARTUP (system disabled) Flow switch is non-functional.
  • Check for dirty or clogged filter cartridge.3.
  • My first thought was OK, I guess I need a brand new pump but noticed that the pump had a sales sticker on the side of it that was not from
  • Filter and circulation pump is activated and the heater is deactivatedDO NOT GET INTO THE WATER.

Jacuzzi Hot Tub Error Codes

SnS = Sensors out of balance. http://www.justanswer.com/pool-and-spa/5moys-cannot-hot-tub-sl-sleep-mode-shut-off.html Spacare.com 888-772-9887 Technical Assistance 405-622-4950 0 Item(s) | Total: $0 Home Shop SpaCare.com Spa Part Index Circuit Board Repair Spa Covers Spa & Hot Tub Covers Spa Cover Lifts Jacuzzi Fl1 Error Message It automatically activates the pump (and the heater if necessary) to circulate the water and warm the plumbing. Jacuzzi Code Cf The J- 355 features 2 deep bucket seats, one lounge and is a deep sitting hot tub.

Condition can cause injury or damage to spa and its components. this contact form Spa is shut down.Pr = When spa is first actuated, it will go into Priming Mode.ILOC = Interlock failure - possible pump or ozone spike .(---) =Unknown water temperature. (Displays when The J-335 is an entry level hot tub with some great jetting.The Jacuzzi Spa J-210 hot tub spa is a 6 person hot tub. Sn2 = Nonfunctional temperature sensor. Jacuzzi Error Code 616

Contact the dealer or service technician if the problem continues.Freeze ProtectionThe spa system has detected a potential freeze condition. What do I do? If display shows only this message (blinking) spa is shut down. have a peek here The fundamental reason is water flow through the spa control system, if the water is not flowing at a rate to satisfy the switch, it will result in one of the

Program setting of spa unit for Economy Mode.3. Jacuzzi Flow Switch If circulation pump is not powering on, try cutting off power at the mainbreaker. Contact qualified service technician.

PnL = Communication between the panel and circuit board is faulty. ---- = "Watchdog" (spa is deactivated) A problem has been detected.

Power on the spa must be cycled before the heater will function again. Do not enter the spa. It is 11/30/2016 11/30/2016 Poolservice123 I can not turn off the waterfall feature on my Sundance Hot 11/29/2016 11/29/2016 JACUSTOMER-27j3luit- My spa keeps kicking the breaker. Fl1 Error Sundance Spa A: This means your spa has deactivated itself and is in watchdog mode.

drops.HL = High limit switch tripped. One sensor has detected 110ºF.Flo = Improper flow or pressure switch malfunction Cool = Water temp 20° below set point ICE = Potential freeze condition has been detected Sn1 = Hi-limit If the flow rate still seems less than normal with all jets and valves open, you may consider inspecting for broken valves (closed when they appear to be open), clogged impeller http://wipidigital.com/error-code/singer-c4-error-message.html drops.hot = Overheating, water over 112° F.

Turned temp up to 104 (was/set at 98) and Heat indicator light came on......Turned power off, replaced filters, powered up checked temp this morning and it was 103......now turned back down It is the small metal sensor attached to the side of the heater tube. Like our previous discussions on spa error codes, FLO and OH, the sensor codes Sn, Sn1, Sn2… are very much water flow dependent. The missus was well impressed......That $60(+) will now be spent elsewhere, hopefully cooling fluids for the (expected HOT) weekend......wet/miserable summer to date ......Big thanks again Jim for your helpWidnes « Last

This setting is not user-programmable.This condition does not kick in until the water temperature climbs to 95°F (35°C). Their models feature eco-friendly and advanced hydrotherapy options, and Jacuzzi Hot Tubs & Spas is headquartered in Chino, California. OPEN SENSOR (heater disabled) or SHORTED SENSOR (hot tub deactivated) The high-limit temperature sensor is non-functional. Brett Aqualine OH = Temp exceeds 118° F Fr = Freeze condition - temp below 40° F FL = Pressure switch failure EO = Shorted temp sensor E1 = Open temp

Reset the countdown timer when finished.FL1 or FL2 (Flashing)When FL1 code starts flashing it means the flow switch is malfunctioning and stuck open-likely because of a dirty filter or because there No action is necessary.