Home > Error Code > Jacuzzi Hot Tub Flo Error

Jacuzzi Hot Tub Flo Error

Contents

You could try jumping out the leads where the pressure switch/flo-sensors plug into the board and see if the heater will click on. Could indicate a flow problem. Ecn = Spa operating in Economy Mode. These sensors are there to protect the heater from running dry, so if the water flow drops below a certain level the sensors will tell the heater to shut down in his comment is here

Problem 2 LF low flow at certain times with no heat, and a dry warning, not sure what that means, but doesn't sound good. Virginia Wood May 9, 2015 at 10:53 pm We have a vita spa. For spas with either a vertical heater or "U" style, it will have a flow switch looking like this: In either case you want to disconnect ONE wire from Let's start at the top, today's post is about water flow trouble codes on your spa panel.

Jacuzzi Hot Tub Flo Error

Categories Consumer Research for Best Hot Tub (100) hottubworks.com (128) life (131) spa chemicals (67) spa covers (161) Spa Crystals (11) spa filter (31) spa heater (26) Spa Ozone (17) Spa Sign in to make your opinion count. You must be logged in to post a comment.

Why a Marquis Spa for Your New Hot Tub? Topside controls also give lots of information about your spa status, which are not to be confused with spa error codes. By far the most common is that the pressure switch/flow switch has failed. Vita Spa Error Codes Sign in to add this video to a playlist.

Jet 2 12/1/2016 12/1/2016 Poolservice123 The fio light and standard light are on simultaneously. Hot Tub Error Codes I'm stumped. Spa has shut down. https://spacare.com/commonspasideerrorcodes.aspx Refer to your owner's manual.

I have replaced the heating element and the pessure switch which is a non-adjustable one. Hydropool Hot Tub Error Codes HFL = Substantial difference between temperature sensors detected. Could also be low water level. The temp sensor is the larger of the two silver bullets.

Hot Tub Error Codes

My temp has been steady at 89, down from my usual 98. recommended you read It has maintained the temp for 3 days. Jacuzzi Hot Tub Flo Error Category Education License Standard YouTube License Show more Show less Loading... Where Is The Flow Switch On A Hot Tub PSoL = Pressure switch open with low pump.

I have changed circ pumps. this content let me know how that works. -Jay Howard July 31, 2014 at 7:32 am I have a Jacuzzi Model J-280 and I get a FS2 error code on the panel when Spa has shut down. For the complete list of error codes click here. Flc Error Code On Hot Tub

  • Here's what to do if your spa throws a FL, FLO or FLOW error code at you.
  • This process will clear the PC board of the error and if the filters were the culprit, your spa should start heating and running normally.
  • Kind Regards Karen admin June 27, 2012 at 9:57 am Hi Karen, I apologize my reply did not post before and I am not sure if you received my email.
  • If I can help further let me know.
  • If so, then I would clean or replace the filter as needed and reinstall.

toby May 15, 2015 at 2:15 pm I have a belize 3000L hot tub my error codes is LOC and FLC at the same time.I did have a flo code as He has been in the pool and spa industry for the last 15 years and is CPO certified by the National Swimming Pool Foundation. Rare system error. http://wipidigital.com/error-code/jacuzzi-fl1-error-message.html How old are the filters?

COOL = Spa water is more than 20° F cooler than the temperature set point. Marquis Spa Error Codes or SpaDepot.com customers with accounts enjoy these benefits: Faster checkout Order status & history Easier package tracking Manage addresses Favorites list Exclusive deals CREATE ACCOUNT SHOP AS GUEST All Products You see if the flow is not at the desired level there is usually a good amount of air in the lines, when a spa heater or motor is running with

The hot tub ran every 4 hours and after the cooling issue, it would only run for a second and turn off for a second, repeating.

Going into detail troubleshooting of flow sensors and pressure switches are two blog posts of their own and I hope to get to that in a future post. Std = Spa operating in Standard Mode. I cleaned them by soaking them in muriatic acid overnight and rinsed them thoroughly. Balboa Hot Tub Error Codes Poolservice123 is online now I have a Balboa Hot tub that consistantly has the "FL" error Customer Question I have a Balboa Hot tub that consistantly has the "FL" error code.

There are a couple of common causes for flow errors in hot tubs; low water level, dirty filters, clogged circulation pumps, and bad flow sensors. FL2 = Pressure switch problem. I topped off the water, both were process of elimination and not required. check over here At the same time this test is being done, put your hand on the stainless steel heater manifold, it should NOT be hot, it should only be at the same temperature

Once I hooked the topside control panel back in, nothing displayed in the red led screen. So if the pump is weak that is your culprit. -Jay Tim December 29, 2015 at 7:19 pm Like the rest of you I have a problem. When the water is not flowing it should be OPEN, not CLOSED, if it is closed replace it. No LF or dry warnings.

Well sorry about long post any any misspelled words. Shawn October 23, 2015 at 2:28 pm Hi. Depending on where the temp sensor is mounted; usually in the wall of the spa in a sensor mount, you could have a flow issue. Did you check the gate valves to make sure 1 of those is no partially blocking the flow, causing the DR error and the pump to over heat? -Jay Ray November

REPLACE. Copyright 2006-14 Clear Creek Spa Service All Rights Reserved Jump to content Existing user? I have taken out the filter but it did not clear it up?? ID the heater.

Over return e past few years it just seems to shut off I can't seem to remember if it ever put out a code or what it was. I wanted to thank you for your time explaining what I needed, as I wasn't 100% sure if what I was ordering was correct. Do I need to replace the pump?