Home > Error Code > Sns Code On Hot Tub

Sns Code On Hot Tub

Contents

Check wiring for burns- especially the ground wire and wires at gas valve. 4. Below is a list of common error codes from the top manufacturers of control equipment for hot tubs. Continue Diagnostic Messages on the Topside Panel Top Next Investigate an Diagnostic Message or Other Message on a Balboa Instruments Topside Panel Display. What does that mean? http://wipidigital.com/error-code/sky-error-code-25.html

If pilot is confirmed, check for 24V minimum out of fan relay to pressure switch. 3. FL = Flow. ToE Time out error. The code only notes that the heater is attempting to spark for ignition and does not denote an error has occurred. weblink

Sns Code On Hot Tub

OH = Over heat. F6 Freeze protection. drops.

Check for clogged filter. There is no action required. This means that there is a flow issue through your heater. Balboa Hot Tub Codes Sl Or at the very least call the manufacturer.

Check water levels at skimmer face. (should be middle of skimmer face) 2. Balboa Hot Tub Error Codes System will restart when temp. dry Inadequate water detected in heater. (Displays on third occurrence of "dr" message). Below is a chart we created to help pool owners identify the meaning of Raypak's fault code.

Sn3 = Open or shorted sensor ( heater disabled). Balboa Sn Error Code If unit does not fire and code reappears, power OFF, disconnect valve wires from board and remove MV, PV, and ground wires. To use the AWS Documentation, Javascript must be enabled. OH = High temperature condition, has reached 110°F.

  • One sensor has detected 110º F.
  • If the sensor is not mounted all the way into the JACO fitting on the header, it may give a false reading.
  • If the problem continues make sure circulation pump is moving water.
  • No action is necessary.
  • ICE = Freeze protection.
  • Pr This message is displayed when your hot tub is first powered on.
  • At 107°F the spa should reset.

Balboa Hot Tub Error Codes

Sign In Sign Up Browse Back Browse Forums Blogs Calendar Staff Online Users Activity Back Activity All Activity Search Spa Builders Spa Side Error Codes For more information regarding Spa Builders tech supportclick here Sn1 Nonfunctional high temperature sensor. Sns Code On Hot Tub The spa is at a temperature above 108° . Sn Error Code Hot Tub PnL = Communication between the panel and circuit board is faulty. ---- = "Watchdog" (spa is deactivated) A problem has been detected.

If unit does not fire, replace the gas valve. 8. http://wipidigital.com/error-code/error-code-67-lg.html If water temperature drops 20°F below set temperature, low speed pump and heater activates to bring temperature within 15° of set temperature. FL1 Water flow problem, inhibited or pressure switch malfunction. drops. How To Fix Sn Code On Hot Tub

If spa doesn’t reset there is an issue with sensors or PC board. Error & LCD Window Message Codes: ACC (Applied Computer Controls) CoLd = Temperature in the spa heater housing is below 40° F. If code reappears, replace board as the main processor failed to start. navigate here If you saw a spark at Ignition Module, turn off the power and reconnect wires. 6.

Check heater location- if more than 5 ft above or below water level- adjust pressure switch. Cal Spa Hot Tub Error Codes Heater disabled but the spa is operational. Categories Consumer Research for Best Hot Tub (100) hottubworks.com (128) life (131) spa chemicals (67) spa covers (161) Spa Crystals (11) spa filter (31) spa heater (26) Spa Ozone (17) Spa

Error codes are both curses and blessings.

It then repeats this cycle for unto 60 minutes before the burners stay lit. th3/39 = On startup indicates water temperature less than 39° F. Usually, the sensor failure error code is SNS. Cal Spa Sn Error Code Do not enter the spa.

Consumer Reviews EasyPak Spa Controls "Very pleased with the ease of installation and all the diagnostic features that other spa packs did not even have. COOL Spa water is more than 20° F cooler than the temperature set point. Heater is deactivated. http://wipidigital.com/error-code/bounce-code-550.html FFLIndicates a false flame signal. 1.

Reply Mo K says: August 22, 2016 at 1:21 PM ROL code shows on my Raypak heater as well as service is blinking, what do need I to do? HL High limit switch tripped. Or maybe it's just me. It will try to spark (spk) but nothing happens.

Heater is shut down, but other spa functions run normally. Wondering what your spa is trying to tell you? hot Overheating, water over 112° F. If the two thermistors are more than 2 degrees apart, the SNS code will appear. 3.

No action is necessary. Backwash if necessary. 4. December 5, 2016 Poolside Repair: How To Install A D.E. PDF | Kindle Terms of Use | © 2016, Amazon Web Services, Inc.

FREE SHIPPING $100+ $0.00 SIGN IN Sign In Registered Customers SIGN IN Forgot Password? Does your unit need a high wind stack? 3. F2 Panel sensors have been pressed too many times in a short period of time. GVOPower found at either PV or MV at the incorrect time.1.

Check your breaker and turn back on, if off. ICE Freeze protection. Try the Forums.Did this page help you?YesNoFeedbackJavascript is disabled or is unavailable in your browser. In some instances it may be more prudent to contact a local repairman or send Spa Care Center your control box for evaluation/repair.

If this code appears and stays on, turn off power to board at toggle switch and source, then re-establish power. 2. Our goal with this blog is to aid you in identifying and defining the error code on your Raypak heater and to provide possible solutions, as per the manufacturer.